DS Audio

PH-001 Armcable

$ 15,999
The highest quality construction throughout
When using an MM or MC cartridge, the cold side of the phono cable serves only as a ground. In the case of optical cartridges however the cold side is used to supply power from the equalizer to the cartridge. Therefore, in such an application, the cold side of the cable is just as important as the signal carrying hot line. The PH-001 features identical materials and construction on both the hot and cold sides ensuring that the power supply is kept stable.

Complete Shielding
Optical cartridges have a relatively high impedance due in part to the photo sensors used in their design. Due to this high impedance, external noise may be picked up if an unshielded phono cable was used. The DS Audio PH-001 is completely shielded with a silver plated copper braid, thus completely illuminating any potential interference.


RCA terminals machined from pure copper
The PH-001 features RCA phono connectors machined from pure copper. The pure copper base conductor is then gold plated. Use of such high quality connectors allows even more musical detail and texture to shine through, along with a heightened sense of openness.
Silver-plated copper conductors
The PH-001 cable features silver plated pure copper conductors, each conductor is made up of 37 strands of 0.26mm diameter wire. This gives a very large overall conductor cross-sectional area of 1.964m㎡ .


PH-001 Phono cable
RCA terminals pure copper terminals
RCA terminal body Aluminum
Cable outer diameter 15mmφ
Cable material Silver plated copper wire
Composition φ0.26mm/37 wires
Conductor cross-sectional area 1.964㎟
Insulator material FEP (fluoroplastic)
Shield Mesh shield
Shield material Silver plated copper wire
Length 1.2m
Specifications

DIN(Straight) to RCA or DIN(L-type plug) or RCA to RCA selectable
※Can be used with MM/MC cartridges without any problem.

ES-001 Eccentricity Detection Stabilizer

$ 43,999
ES-001 Eccentricity Detection Stabilizer
Size
φ80×H70mm
Weight
620g(including batteries)
Material
Aluminum& Tungsten
Power supply
Two AA batteries
User Interface
Touch panel (2.4inch)

Vinyl lonizer #ION-001

$ 13,999
THE ION-001 IONIZER RETRICTS THR GENERATION OF OZONE BY CONTROLLING THE POWER SUPPLY VOLTAGE PROPERLY, AND IS DISIGNED TO HAVE A CONCENTRATION OF 0.01 PPM OR LESS. THEREFORE, THERE IS NO CONCERN SUCHNAS OXIDATION BY OZNE.

THE IONIZER ITSELF HAS A LIFETIME (APPROXIMATELY)AMOUNT OF IONS AFTER 10,000 HOURS OF USE). PLEASE TURN OFF THE POWER WHEN NOT USING THE IONIZER, IT TAKES ABOUT 10 YEARS TO USE 10,000 HOURS FOR 3 HOURS EVERY DAY.

THE CHARGE DEGREE OF THE RECOORD DIFFERS DEPENDING ON THE ENVIRONMENT SUCH AS TEMPERATURE AND HUMIDITY .

DO NOT PUT YOUR FINGER OR STICK INTO THE IONIZER OULTET AS IF MAY CAUSE A MALFUNCTION.

SPECIFICATION :-

SIZE: 84MM X 84MM X 250MM

WEIGHT: 950G

INPUT VOLTAGE: DC12V (AC100V-240V0

NUMBER OF IONIZERS: POSITIVE (+) ION X 2 NEGATIVE (-) X 2

AMOUNT OF OZONE: LESS THAN 0.01PPM

Headshell HS-001

$ 3,399
Technical Data
Material Ultra duralumin
External dimensions H 21 × W 40 × D 55 mm
Connector part Aluminum
Connector terminal Gold plating
Connector terminal Gold plating
Shell lead wire Litz wire 4N φ 0.08 x 10 x 3 yore rings
Weight approx 10.5 g (excluding shell lead wire)
11.0 g (including shell lead wire)
Screws Stainless steel bolt
M 2.6 L 8 × 2, M 2.6 L 12 × 2
M2.6 SUS but×2