Mobile reference DAC/ head amp
Fully balanced 4.4mm outputs with 4,100mW output
Devilishly deep bass reproduction and unbelievable resolution
New PureWave ultra-low THD circuit design - THD 0.002% (BAL), 0.001% (SE)
Packed full of audiophile-grade parts and state of the art features, it would be sinful to miss it.
Dual DAC with 8 channels
32/768kHz and DSD512 with MQA decoder
Ultra-low noise, low distortion, (0.00006%) OC2028 OpAmp
S/pDIF in (3.5mm and Optical)
Dedicated USB-C charging port with BC1.2 fast-charge
Comes with the new iFi Traveller carry case and:
Square to round fibre conversion head
USB-Type A to Type-C cable
6.35 to 3.5 converter
5.5* 2.1 female to Type-C power cable
4.4mm to Twin XLR cable
Digital Inputs USB 3.0 type A “OTG” Socket
(USB2.0 compatible/with iPurifier® technology built-in)
S/PDIF (3.5m coaxial/optical)
Output balanced: 4.4mm SE: 6.3mm/RCADAC
DAC Bit-Perfect DSD & DXD, PCM DAC by Dual-core Burr Brown
Clock Ultra low jitter GMT Femtosecond Clock
DSD Extreme/Extended/Standard Bandwidth
DXD Bit-Perfect Processing
Dynamic Range (Line) >117db(A)
THD & N (0dBFS Line) <0.003%
Output Voltage (Line) >2V
Output Impedance <240Ω
Jitter (correlated) Below AP2 test set limit
Headphone Power Output
Turbo Mode Power (max) 10.0V/4,100 mW
Power (continuous) >1,560 mW @ 64 Ohm
>166 mW @ 600 Ohm
Normal mode Power (max) 5.5V/1,900 mW
Power (continuous) >100 mW @ 300 Ohm
>950 mW @ 32 Ohm
Eco mode Power (max) 2.0V/500 mW @ 8 Ohm
Power (continuous) >250 mW @ 16 Ohm
Dynamic Range (HP) >115dB(A) (Eco Mode, 2V Out)
THD &N (HP 500mW/16R) < 0.008%
Output Voltage (HP) >10V (Turbo Mode)
Output Impedance <1Ω (iEMatch not engaged)
Maximum Output Power 4,100 mW @ 16 Ohm Load
Continuous Output Power 1,000 mW @ 64 Ohm Load
Battery Lithium-polymer 4800mAh
Power System charging via USB-C, BC V1.2 compliant
up to1500mA charging current
Dimensions 172 x 67 x 27 mm 6.8" x 2.6" x 1.1"
Weight 295 g (0.65 Ibs)
The ‘magic’ of tubes from solid-state.
Our Class A TubeState® technology is the result of nearly four decades of research of our Chief Designer, Thorsten Loesch, on tube and transistor gear.
The key is not to add distortion, but to avoid certain types of distortion. Once it is understood that specific distortions are endemic to solid-state circuitry and are pernicious with respect to subjective sound quality, we eliminate these from solid-state circuitry, without adding on tube-like distortion and noise.
Read more in our Tech Note.
Precisely match up LP equalisation!
Listen to vinyl recordings in the original and correct way. When so much is invested in an audio system, to leave out the final few percent of correctly matching the equalisation to the LP is almost sacrilege.
Our list of LP recommendations with their precise EQ curve will show you how using the correct EQ curve makes one heck of a difference! We reckon you probably have some of our picks in your collection.
Discover more about the history of recordings and EQ curves here.
Look, mum. No output coupling capacitor.
Direct Drive Servoless® is an important element of the audiophile experience, which is not visible in measurements but is quite audible.
Unlike a standard phono stage design, the iPhono3 Black Label continues the special design tradition of being direct coupled (i.e. no coupling capacitor) from cartridge to output and it does so without requiring a conventional DC servo.
In the iPhono3 Black Label the unique DC-Infinity circuit boosts the circuits DC gain to approach infinity (it is approximately 1 trillion one million times one million; 1012).
Once the feedback loop is closed, this near-infinite DC gain cancels all offset voltages to deliver a direct-coupled output with 0V DC offset. The key to the DC-Infinity circuit is that it only changes the gain below approx. 0.01Hz, while leaving the AC behaviour of the circuit at higher frequencies unchanged, injecting neither noise nor distortion into the audio signal.
Any noise and distortion of the DC-Infinity circuit happens at the same signal level as the output signal and is by design around 100 times less than the noise and distortion of the actual amplifier circuit, so compared to the actual phono stage noise and distortion it effectively disappears.
Nichion audio-grade capacitors, Panasonic OSCON/ECPU capacitors, MELF resistors, TDK C0G capacitors…the list goes on.
The iPhono3 Black Label is jam-packed. Take a look at its internals. Read more here.
Brand new power supply tech to power the iPhono3 Black Label.
iPower X. What’s not to love?
Frequency Response 10Hz – 100KHz (±0.3dB) 20Hz – 20kHz (±0.2dB)
Dynamic Range MM (36dB): > 108dB (A-weighted) MC (60dB): > 106dB (A-weighted)
Signal-to-Noise Ratio MM (36dB): > 85dB (A-weighted re. 5mV) MC (60dB): > 85dB (A-weighted re. 0.5mV)
Overload Margin MM (36dB): > 26dB (re. 5mV, @ 1% THD) MC (60dB): > 22dB (re 0.5mV, @ 1% THD)
Crosstalk <-71dB (1KHz)
Maximum undistorted output 7V (Load >= 600 Ohm, THD <=1%)
Total Harmonic Distortion (THD) <0.005% (MM 36dB 1V out 600R Load)
Output Impedance <100Ω
Input Voltage AC 100 – 240V, 50/60Hz
Power Consumption < 5W. Use with iPower X (15v) do NOT use any other power supply.
Dimensions 6.2' x 2.3' x 1.1' / 158 x 58 x 28 mm
Weight 0.58 lbs / 265 g
In order to improve upon the sector-defining original iPhono, whilst keeping in essence the same design philosophy, our design team went back to the beginning and designed a ground-up, new iPhono2. The design, circuitry, the parts, the specifications and most important of all, the sonic performance meant the end justified the means.
The iCAN – Special Edition is a ‘specially-tuned’ version of the top-selling micro iCAN. Sonically, it boasts Class A, DirectDrive® and TubeState®. Features wise, it features a newly-refined XBass®, 3D Holographic® for headphones and 0dB, 12dB and 24dB Gain adjustment. Powered by the all-new iPower (15V), the special Turbo headamp® circuit pumps out 4,000mW to drive even the most demanding of headphones.
Creating a one-box-fits-all-headphones amplifier was a challenge. That’s because headphones are a diverse lot. So when our engineers designed the new iCAN, they didn’t start with the amplifier; they started with the headphones.
Unlike traditional headphone amplifiers, the design of the iCAN is based on the whole gamut of headphones. This atypical approach has bestowed upon the iCAN a unique ability to realise the full potential of each and every headphone.
First and foremost, it was designed for the finest sound quality. With XBass you hear deeper, richer and cleaner bass. The 3D Holographic Sound system creates headphone-based music that is free-flowing rather than restricted.
The iDAC was good. It was very good and cultivated a very loyal following among customers and reviewers alike.
The iDAC2 is the all-new 2015 version. It is a totally new design that has drawn upon the widespread praise garnered by the nano iDSD and micro iDSD.
The original iTube became the ‘go to’ tube buffer for any and every home audio system. We have redesigned the micro iTube2 with new parts and new circuitry using trickle-down technology from the flagship ‘Pro’ series. Only the GE5670 tube remains.
The micro iTube2 is a tubed output stage, tube preamp, tube buffer AND an impedance-matching device all in one. There is nothing like it. You can put the micro iTube2 before a solid-state preamp and another one after it, creating the effect of tubing the whole audio chain. Or you can choose to simply use the micro iTube2 as a very high-quality preamp by itself.
The micro iTube2 sounds by and far, like a tube amplifier ‘done right with the inimitable magic of tubes.‘ Tonality and heft, especially in the mid-range and bass frequencies are increased to elevate the whole audio system from $100k to $1k. The micro iTube2 injects a serious does of tube magic into any audio system.
‘Magic’ of SET, Push-Pull or Classic Tube sound
In the ‘magic of tubes’ listening stakes, the iTube2 offers the listener the choice of different key sonic signatures:
– a Single-Ended Triode power amplifier;
– a Push-Pull tube power amplifier;
– a classic tube amplifier.
Just to note from the iFi team – there is no ‘right’ setting. We advise you to set according to your systems synergy and your listening preferences.
XBass+® matrix for Speakers, new and improved
XBass+® for Speakers is quite different to its sister technology XBass+® for Headphones. The only similarity is in philosophy as the ability to enhance your Speaker listening is quite different to enhancing Headphone listening.
The former gives each and every audio system adjustable levels of bass control to enhance listening enjoyment through speakers that have limited bass extension. We have taken great care to ensure no degradation in sound quality occurs.
20 Hz (6dB): For speakers missing only the lowest bass notes (below 40Hz).
20 Hz (12dB): For speakers missing some bass notes (below 80Hz).
OFF: XBass+ switched out.
3D Holographic+® matrix for Speakers
The latest 3D Holographic+ matrix for Speakers offers something quite special. It takes high-end systems to another level of performance. It was drawn from the original ground-breaking work of Alan Blumlein, the ‘father of stereo.’
Firstly, it corrects the fundamental spatial distortion in recordings. And secondly, it increases the width of the soundstage beyond that of the speaker placement.
30˚+ This matrix adds an extra 30˚ to redress the narrow placement of speakers (eg either side of a PC monitor).
+ This matrix recreates original ‘width’ of the soundstage and is the recommended DEFAULT setting.
Off 3D+ switched out.
Brand-new PCB, Direct-Coupled for purest signal path
The iTube2, in-line with the latest iFi products, is ‘Direct-Coupled.’ This means no output coupling capacitor for the purest, most direct signal path.
Furthermore, the iTube2 is virtually a whole new product as the circuitry and components have been radically changed and it now is more closely connected to the Pro iCAN. Trickle-down from flagship range? A definite “yes!”
Reference class parts quality
The iTube2 employs Japan TDK C0G type capacitors. These are complimented by Japan Panasonic ECPU Film Capacitors explicitly designed for audio use with extremely low distortion (<0.00001% @ 1V/10kHz).
The iTube 2 also uses ELNA SIlmic capacitors. These and other parts are only found in components with an extra ‘0’ to the price.
The proof is in the listening. The best tube buffer/pre-amp out there just pulled even further ahead.
Running silently in the background – iPower 15v
Every iTube2 comes with the very-new iPOWER (15v) which is a remarkable-quiet, advanced DC power supply that features:
The iFi iRACK puts the iFi range above the competition – figuratively and literally. It is able to run from 1 shelf through to four shelves. Both the award-wining micro series and newly-launched nano series fit the iRACK. Its specially-designed slots minimise resonance and ensures a perfect fit for each and every iFi unit.
• Non-magnetic stainless steel pillars with micro-vibration control.
• Resonance-damped Organic Glass shelves
• Natural rubber ‘O’ rings.
• Precision-machined spikes with matching cups
• RCA cables set included